|
|
|
Kto jest w sklepie?
Sklep przegląda 5817 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
MEASUREMENT OF MICROWAVE POWER OUTPUT
¥ Microwave power output measurement is made with the microwave oven supplied at its rated voltage and operated at its maximum microwave power setting with a load of (1000±5) g of potable water. ¥ The water is contained in a cylindrical borosilicate glass vessel having a maximum material thickness of 3 mm and an outside diameter of approximately 190mm. ¥ The oven and the empty vessel are at ambient temperature prior to the start of the test. ¥ The initial temperature (T1) of the water is (10±2)¡C It is measured immediately before the water is added to the vessel. After addition of the water to the vessel, the load is immediately placed on the center of the turntable which is in the lowest position and the microwave power switched on. ¥ The time T for the temperature of the water to rise by a value � T of (10±2)¡K is measured, where T is the time in seconds and �T is the temperature rise. The initial and final water temperatures are selected so that the maximum difference between the final water temperature and the ambient temperature is 5¡K.
Â¥ The microwave power output P in watts is calculated from the following formula : P=
4187 X (DT) + 0.88 X (T2 - T0) X M T
¥ T2: Temperature after heating ¥ T0: Temperature after bowl ¥ M: Weight of bowl
is measured while the microwave generator is operating at full power. Magnetron filament heat-up time is not included. (about 3 sec) ¥ The water is stirred to equalize temperature throughout the vessel, prior to measuring the final water temperature. ¥ Stirring devices and measuring instruments are selected in order to minimize addition or removal of heat.
WATER LOAD
TURNTABLE
DISASSEMBLY AND ADJUSTMENT
A. OUTER CASE REMOVAL
1) Disconnect the power supply cord from the outlet. 2) Remove the screws from the rear and along side edges of the case. The outer case must be moved backward to be lifted off.
C. CONTROL PANEL ASSEMBLY
1) Disconnect the leadwire from the PCB SUB ASS�Y. 2) Remove the screws for the earth and securing the control panel. 3) Lift control panel ASS�Y from the oven by the tab unhooked.
B. POWER SUPPLY CORD
1) Remove the outer case. 2) Disconnect two terminals, and remove one screw of the earth terminal.
CAUTION: DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE SERVICING (refer to page 2-1)
5-3
|
|
|
> |
|
